Formax FD 8302CC/SC Instrukcja Użytkownika Pobierz pdf

FD 8302CC Cross-Cut Shredder

FD 8302SC Strip-Cut Shredder

OPERATOR MANUAL

FIRST EDITION

5/13

Safety Devices and Other Features

Formax 8000 Series Shredders are equipped with various safety features:

Automatic Reverse Rotation

When too much paper is inserted, the cutter stops operating and

automatically rotates in reverse to discharge the jammed paper. An alarm

sounds. Reduce the amount of paper and restart the operation.

Door Switch

If the door is open, the shredder will not operate.

Automatic Stop

When the shredded paper lls the wastebasket, the “FULL” light

comes on and the cutter stops operation. Open the door, remove the

wastebasket and empty paper scraps. Replace the wastebasket, close

the door and continue operation.

Automatic Power Shut-Off

• If the shredder operates continuously for more than 30

minutes, the power is automatically shut off.

• If the motor is overloaded, the “STOP” LED will ash until it cools

down. When the ashing stops the shredder is ready to be used again.

Maintenance

• Disconnect power by pulling power cord plug from wall outlet.

• To clean the exterior, wipe the surface with a soft cloth. If the surface is very dirty, use

a neutral detergent, then wipe again with a soft cloth.

CAUTION:

• Never put water directly on the surface of the shredder.

• Never clean the case with benzene or thinner, since it will cause discoloration.

• Do not dismantle the shredder. Contact your Formax Dealer for service.

Oil Indicator

The “MANUAL” LED will ash after every four (4) hours of operation as an indicator to

oil the shredder cutting blades. The LED will continue to ash until oiled. NOTE: the

shedder will still operate when the LED is ashing but at a decreased load capacity.

To oil: Spread shredder oil onto the cutters through the feed opening, and allow the

oil to sit for a few minutes to permeate the cutting blades, then press the “REV” button

and hold for ve seconds. “MANUAL” and “REV” LED indicators on control panel will

light. The shredder will operate in reverse for one minute, then the “AUTO” LED will light

indicating the shredder is ready.

1 2

Podsumowanie treści

Strona 1 - FIRST EDITION

FD 8302CC Cross-Cut ShredderFD 8302SC Strip-Cut ShredderOPERATOR MANUAL FIRST EDITION5/13Safety Devices and Other FeaturesFormax 8000 Series Shredd

Strona 2 - FD 8302CC FD 8302SC

Operation1. Flip the power switch “ON” located on the right side of the shredder. 2. Auto Start/Auto StopWhen the START button is pushed, the signal l

Powiązane modele: FD 8400HS | FD 8714CC | FD 8602CC/SC | FD 8300HS | FD 8502AF | FD 8402CC/SC | FD 8502CC/SC | FD 8704CC | FD 8650CC | FD 8652CC |

Więcej dokumentów dla Niszczarki Formax FD 8302CC/SC

Aby wyświetlić dokument Formax FD 8302CC/SC Instrukcja Użytkownika

Formax FD 8302CC/SC Instrukcja Użytkownika (-1 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Formax FD 8302CC/SC Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Niszczarki Formax FD 8302CC/SC. Formax FD 8302CC/SC User Manual Instrukcja obsługi

Podsumowanie treści

Powiązane modele: FD 8400HS | FD 8714CC | FD 8602CC/SC | FD 8300HS | FD 8502AF | FD 8402CC/SC | FD 8502CC/SC | FD 8704CC | FD 8650CC | FD 8652CC |

Więcej dokumentów dla Niszczarki Formax FD 8302CC/SC

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Niszczarki Formax FD 8302CC/SC