Formax FD 8500HS Instrukcja Użytkownika Pobierz pdf

High Security Paper Shredder

FD 8500HS Cross-Cut / Level 6

OPERATOR MANUAL

FIRST EDITION

10/08

Safety Devices and Other Features

Formax 8000 Series Shredders are equipped with various safety features:

Automatic Reverse Rotation

(Process takes about 6 to 8 seconds)

When too much paper is inserted, the cutter stops operating

and

automatically rotates in reverse to discharge the jammed paper. An

alarm sounds. Reduce the amount of paper and restart the operation.

Door Switch

If the door is open, the shredder will not operate.

Automatic Stop

When the shredded paper ﬁ lls the waste bin, the “FULL”

light comes

on and the cutter stops operation. Open the door, remove the waste

bin and empty paper shreds. Replace the waste bin, close the door

and continue operation.

Automatic Power Shut-Off

• If the shredder operates continuously for more than 30

minutes,

the power is automatically shut off.

• If the motor is overloaded, the “STOP” LED will ﬂ ash until it cools

down. When the ﬂ ashing stops the shredder is ready to be used

again.

Oil Indicator

Oil regularly for peak performance

NOTE:

High Security shredders require

a specialized oil that can only be ordered through Formax, part # 8000-15

The

“MANUAL” LED will ﬂ ash after every four (4) hours of operation as an indicator to oil

the shredder cutting blades. The LED will continue to ﬂ ash until oiled. NOTE: the

shedder will still operate when the LED is ﬂ ashing but at a decreased load capacity.

To oil:

Spread shredder oil onto the cutters through the feed opening, and allow the

oil to sit for a few minutes to permeate the cutting blades, then press the “REV” button

and hold for ﬁ ve seconds. “MANUAL” and “REV” LED indicators on control panel will

light. The shredder will operate in reverse for one minute, then the “AUTO” LED will

light indicating the shredder is ready.

Maintenance

• Disconnect power by pulling power cord plug from wall outlet.

• To clean the exterior, wipe the surface with a soft cloth. If the surface is

very dirty,

use a neutral detergent, then wipe again with a soft cloth.

CAUTION:

• Never put water directly on the surface of the shredder.

• Never clean the case with benzene or thinner, since it will cause discoloration.

• Do not dismantle the shredder. Contact your Formax Dealer for service.

NSA Approved

Meets the requirements of NSA/CSS speciﬁ cation for

Level 6 High-Security cross-cut shredders.

1 2

Podsumowanie treści

Strona 1 - High Security Paper Shredder

High Security Paper ShredderFD 8500HS Cross-Cut / Level 6OPERATOR MANUAL FIRST EDITION10/08Safety Devices and Other FeaturesFormax 8000 Series Shr

Strona 2 - Safety Precautions

Operation1. Open the door and ﬂ ip the breaker switch to the “ON” position. Close door. Press the Power Switch on the right side of the shredder to t

Powiązane modele: FD 8650CC | FD 8302CC/SC | FD 8400HS | FD 8714CC | FD 8602CC/SC | FD 8300HS | FD 8502AF | FD 8402CC/SC | FD 8502CC/SC | FD 8704CC | FD 8652CC |

Komentarze do niniejszej Instrukcji

Brak uwag

Formax FD 8500HS Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Niszczarki Formax FD 8500HS. Formax FD 8500HS User Manual Instrukcja obsługi

Podsumowanie treści

Powiązane modele: FD 8650CC | FD 8302CC/SC | FD 8400HS | FD 8714CC | FD 8602CC/SC | FD 8300HS | FD 8502AF | FD 8402CC/SC | FD 8502CC/SC | FD 8704CC | FD 8652CC |

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Niszczarki Formax FD 8500HS